Kawasaki Vulcan 750 Forum : Kawasaki VN750 Forums - Reply to Topic
Wheels, Suspension and Brakes
Everything to do with wheels, tires,
suspension, forks and brakes

Thread: Could anyone take a measurement for me? Reply to Thread
Title:
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now



In order to be able to post messages on the Kawasaki Vulcan 750 Forum : Kawasaki VN750 Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

Once registered, your User Name"cannot be changed". We can make exceptions within 7 days, but after that, it is set in stone.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
02-17-2009 02:28 PM
Custom Cow I definetly thank everyone who is working on this for me...I think these things will bolt on...I just want to be sure before spending any money, ya know.
02-17-2009 05:49 AM
750Doug I checked with other members here who I thought would have loose swing arms for easier measure and got 11.5" width at the pivot point. (Thanks AJ and Cindy)
02-15-2009 11:58 AM
Custom Cow My bike is 18 1/2 here...which if this is 19 3/8 on yours will give me a little rearward movement...good thing. But that will mean I need a driveshat also.




Heres a quick diagram to help with numbers I need (if anyone has a arm thats off the bike) Well call them Length / Front / Rear
The overall rear axle length will still be helpful, just not biblical...but I wasnt sure if anyone had a torn down bike laying around.
I appreciate your help Doug...I know I had a tough time measuring the front on the bike...mine looks 12...but a verify on a loose arm would be great.



Thanks again!
02-14-2009 08:02 PM
750Doug I'll get it tomorrow if nobody else has by then.
02-14-2009 08:00 PM
Custom Cow No problem...thank you.

While I was writing that I thought about the axle width...

Im just detrmining if its a bolt in swingarm...I know it uses the same pivot bearings, etc.

Peace man
02-14-2009 07:57 PM
750Doug Pivot to axle 19 3/8"

Swing arm width at pivot 12"

Since I just came in from taking those measurements and see you've posted asking for the axle width, I'll save that for somebody else cause of all the snow and **** I have to trudge though (again) to get out there.
02-14-2009 07:54 PM
Custom Cow Nice bike dude...

I read through your progress thread...Im definetly moving toward that hardtail, spring seat mod....

but for now, I have a Vulcan front wheel and a stock ZN700 wheel in the back
Ive got to change the rear and want a Vulcan to match, Ill need to ditch my disc brake and use the drum...hence the vulcan swingarm...I hope its a bolt in swap...otherwise Ill just fab the stuff I need to change it.

Im sort of hoping the vulcan swing arm is a shade longer as my wheel seems too far forward, an inch or two would make a big difference in look. My bike has a narrow 16 inch wheel and will look good with that fatter 15 on it also.

Hey while your measuring, could you give me an axle width also? outside to outside is fine.

I know our bikes share the same diff...but I dont know if the swing arm may be wider overall.

Peace and thanks.
02-14-2009 06:25 PM
Scoop Sorry, I am travelling and can't get the measurements for you - I would otherwise. But sounds like you've got some frame mods in mind. Just curious what you might be up to!
02-14-2009 04:13 PM
Custom Cow
Could anyone take a measurement for me?

Easy one first

centerline to centerline from the rear axle to the swing arm pivot.

A bit tougher...

the width at the swing point of just the arm itself where it attaches to the frame.

Thanks!

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome