Kawasaki Vulcan 750 Forum : Kawasaki VN750 Forums - Reply to Topic
VN750 General Discussion

Thread: tool box lock fell out Reply to Thread
Title:
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now



In order to be able to post messages on the Kawasaki Vulcan 750 Forum : Kawasaki VN750 Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

Once registered, your User Name"cannot be changed". We can make exceptions within 7 days, but after that, it is set in stone.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
10-01-2014 05:05 PM
lordbutz i got the lock installed. i just had to cut a little slit in the existing slot to accept the new cam that came with the lock set and it works like a dream. i even made a little video of it. i'm gonna be a youtube super star.
09-30-2014 07:03 AM
VN750Rider/Jerry I like cheap, but it is not always possible. I'm about to replace the entire pickup coils and wire assembly ($160) because the insulation inside the engine has hardened and is breaking off. Might as well do it right while the engine is out, rather than put it all back together and have it short out on me hundreds of miles from home. Hopefully I will get at least another 20,000-30,000 miles out of all this, which will make it very cheap compared to buying another bike (which could have problems)
09-29-2014 09:16 PM
OleDirtyDoc Iid do the cabinet lock.i like cheap
09-29-2014 04:58 PM
VN750Rider/Jerry On my '93, bought new, I lost the lock. Dealer replaced it free. Tool box door later broke off, but I did not loose it. I replaced it with a new one, then never used it again. The small amount of room in that compartment is not worth much. It would be convenient, if not for the door breaking off if you actually use it, but I found someplace else to keep things. I thought about putting a cabinet hinge on it, but would rather it look stock.
09-27-2014 10:13 PM
Knifemaker This has always been an issue with this bike, and I made it my #2 suggestion the fifth post inthis thread:
https://www.vn750.com/forum/showthread.php?t=9127

Sorry you didn't get this info sooner. At the old yahoo group we sent out a list of "must do's" to every new member. Seems we can't do that here for those requesting membership. Sorry.

So do read through that thread. Your swingarm caps are also prone to falling off BTW.....
09-27-2014 09:38 PM
lordbutz thanks man. i'll check out the desk lock thing. i would just leave the tape there but i'm trying to sell this thing. my dream bike is a honda interceptor.
09-27-2014 07:38 PM
Vulcan2000
Quote:
Originally Posted by lordbutz View Post
i know its a common problem for the lid itself to fall off but has anyone ever had the lock fall out? it was in a parking garage at the time and i made a report with security but they havent called me back so i'm not sure if it fell out while riding there or if someone popped the lock out but left the wrenches and papers i kept in there.

duct tape is doing a great job of holding the door closed right now but i am on the hunt for a more permanent solution.
Several members have used a cabinet door lock available at Lowe's or Home Depot with success. They are easily trimmed if necessary to get the correct locking arm length. Cut the opposite end from where the arm actually clamps (locks) onto the inside of the tool box and drill a new end hole. Good luck. If you do find a Kawasaki lock setup there is a thread on changing the lock pins so that it will be keyed the same as your ignition key if you want.
09-27-2014 07:30 PM
lordbutz
tool box lock fell out

i know its a common problem for the lid itself to fall off but has anyone ever had the lock fall out? it was in a parking garage at the time and i made a report with security but they havent called me back so i'm not sure if it fell out while riding there or if someone popped the lock out but left the wrenches and papers i kept in there.

duct tape is doing a great job of holding the door closed right now but i am on the hunt for a more permanent solution.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome