Kawasaki Vulcan 750 Forum : Kawasaki VN750 Forums - Reply to Topic
Where does this wire go?
Includes Electrical mods, Lights, Stator,
Rectifier, Diagrams, etc

Thread: Snapped tail light Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Kawasaki Vulcan 750 Forum : Kawasaki VN750 Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

Once registered, your User Name"cannot be changed". We can make exceptions within 7 days, but after that, it is set in stone.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
01-21-2012 10:30 AM
AGStrange OK, thanks, my mechanical abilities are limited, as are my tools.
01-20-2012 07:03 PM
wib714 I used a pin out of a door hinge on mine, wrap it with duct tape then wrap that with black electrial tape. does not look bad at all. electrical tape alone will stretch after a while especially in the heat! thought I had some pics but dont see them on my photobucket account
01-20-2012 06:47 PM
wib714 700 plus, 250 to do it yourself in about 18 hours or so depending on your mechanic abilities. there are plenty of walkthroughs, modifications and help right here on the boards!!!
01-20-2012 05:57 PM
AGStrange Speaking of which, does anyone know what the going rate for a mechanic's replacement of a stator is nowadays?
01-16-2012 04:21 PM
AGStrange Thanks again! Before I do any kind of modifications (other than fixing the tail light), I need to get her running again. She hasn't run in over 2 years and I don't feel like I can tackle replacing the stator (assuming that's what it is); the R/R I could probably do, but I don't know which is the problem ... or if both are the problem.
01-16-2012 03:47 PM
kanuck69 Sounds like a good time to do a signal shave!
01-16-2012 03:36 PM
kc2dgq I would try some aquarium RTV...the kind they use to hold glass aquariums together and keep it water tight as well.

I admit I never tried it for this application, but I have used it where I needed a good bond and it has always performed well. You might want to test it on a small area just to be sure, but definitely inset something in the stalks to keep them from "sagging". The vibrations and bouncing during normal driving could break the bond if there is no support.

Good luck! and let us know how you make out
01-16-2012 10:15 AM
AGStrange OK, thanks!
01-16-2012 10:02 AM
flitecontrol A better repair is to insert the cut down barrel of a ball point pen or similar sized metal tubing into the rubber stem. You will need to split whatever you use to slide the wires into it. If you use metal tubing, you'll need to smooth all the edges to prevent the wires from chaffing against it. Use clear silicone to glue the break and tube insert.
01-16-2012 08:52 AM
Snapped tail light

To make a very long story short, an item in my garage hit the left tail light on my 1992 VN750 and snapped it. The light itself is still attached. Obviously I could use something like duct tape to make it horizontal again, but I was wondering if anyone had experienced a similar accident/incident and whether some kind of "Krazy Glue" would work on the rubber, or if it just pays to look to buy a replacement altogether? Thanks.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

For the best viewing experience please update your browser to Google Chrome