Kawasaki Vulcan 750 Forum : Kawasaki VN750 Forums - Reply to Topic
Transmission / Rear End
\ Chattering Clutch? Transmission Trouble?
Rear End Woes? Splines Shot? Discuss it here!

Thread: Oil Spatter from Final Drive Reply to Thread
Title:
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now



In order to be able to post messages on the Kawasaki Vulcan 750 Forum : Kawasaki VN750 Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

Once registered, your User Name"cannot be changed". We can make exceptions within 7 days, but after that, it is set in stone.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
04-27-2019 07:31 AM
VN750Rider/Jerry A bad seal will cause that, but so will too much grease on the splines (the ones that mesh with the rear wheel) will to. I used to use Kawasaki shaft drive oil, but I don't think Kawasaki makes shaft drive bikes anymore. When you said wash, I hope you didn't mean pressure wash. That will destroy seals quickly. I recently bought a 1997 with 21,000 miles on it. The back wheel was filthy. But none of it looked recent, The final drive was full of decent looking oil, and both the wheel and driveshaft splines have grease on them. Oh, there is also a small vent hole on the inside of the final drive unit behind the wheel. If you seriously overfill the final drive, oil can come out through that.
04-26-2019 11:27 AM
Hellen Brownsville That's your bike on Flickr? Looks RAD!
10-03-2018 12:40 PM
Knifemaker
Quote:
Originally Posted by timgill View Post
Thanks for the info, guys. Checking the splines is on my list too. What's the general consensus on the best brand/source/type of gear oil to use?
Use a full synthetic. I use Mobil One 70w-120. Any weight that covers 90w will do.
10-03-2018 11:30 AM
timgill Thanks for the info, guys. Checking the splines is on my list too. What's the general consensus on the best brand/source/type of gear oil to use?
10-02-2018 08:16 PM
michiganteddybear yea, excess grease on them splines will do that.. ask me how I know..

it takes a very very thin layer of grease on them to be good. Unlike the driveshaft splines which like a lot
10-02-2018 06:05 PM
Spockster x2 - Yep, looks like a seal.

edit: You also can get that on the wheel if you use too much grease on the wheel splines. Where the wheel hub splines to the final drive, not the driveshaft splines.

manuals in my signature.
10-02-2018 04:32 PM
roadpouring Bad O-ring and/or seal. Don't run it without filling with gear oil, just up to the female threads in the filler hole with the bike on center-stand.

Probably need to disassemble the whole thing, check spline lubrication, replace various O-rings, defective parts and clean brakes.


Download a manual. See Spockster's posts for link.
10-02-2018 04:01 PM
timgill
Oil Spatter from Final Drive

I have a significant amount of oil spatter on the rear hub coming from the final drive; see attached pic. This is after about 400 miles of riding since the last wash. Any ideas as to what to check to correct this?

I just recently bought the bike and have no record of the last service of the final drive. Bike is now at about 32000 on the odo.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome