|Topic Review (Newest First)|
|05-22-2017 05:47 PM|
I bought my Engine Guard from Eusjma a couple of weeks ago but I have not yet installed it. I can wait until I do the stator and damper replacement.
Last week I received my new Mosfet R&R kit and also went to West Marine and bought the nuts and bolts to do the MCCT conversion, all in Stainless Steel. The only things I donít have yet are the Bonded Sealing Washers.
In my tool box of scale model supplies, I should have some .020 sheet plastic so I could make my own non-magnetic feeler gauge to do Abyssdncrís Pickup Coil mod.
Now I need to order the rest of the stuff on Uberís ULTIMATE Stator-Damper Parts List and when I do the job Iíll just get all this stuff done at once.
|05-22-2017 04:01 PM|
Brand new thread with all the parts you need for the job.
Hope it helps: ULTIMATE Stator-Damper Parts List
|05-22-2017 01:19 PM|
mostly you will need the normal supplies.
a couple gaskets, fluids, ect. I know that a full list of the parts needed to change the dampers (which includes parts needed for the stator, minus the stator) is somewhere here on the site. Locktite is needed on 1 bolt.
the dampers are made of hard rubber. they tend to break down over time, however, I got at least 40+K on mine when I changed them while doing my stator. it depends a lot on past maintainance history. you dont want them to fail while riding, thats for sure, as the gear can eat the case up.
|05-22-2017 12:57 PM|
I am going to stop at the base Hobby Shop and talk to the guy who runs the place to let him know I am planning to bring the bike in and it might need to stay overnight.
Once I have all the parts together, I'll take a couple of vacation days to give myself a four day weekend and try to knock this out on a Thursday and Friday.
I've been looking at Stators. Is there a specific stator that you guys can recommended?
Also, since it has been suggested that I do the balance dampers while I'm in there, I was trying to find out more about them and read one reference to them breaking down. What are these things made of?
Anything else I need to order for this job? Gaskets? Lock-Tite? etc
|05-21-2017 01:14 PM|
Originally Posted by Knifemaker View Post
|05-21-2017 12:51 PM|
|Knifemaker||Bike won't run without a battery...|
|05-21-2017 12:43 PM|
Originally Posted by ubertalldude View Post
Dang, man. And to think I was offered a job at Mayport, in Jacksonville last June, but they couldn't match the pay I'm getting down here.
Though one of my friends from work had an idea! My battery is in his shed, charging right now and he mentioned The Hobby Shop, on base. The Hobby Shop is a 'Do The Work Yourself', set up. They have about six bays, two with lifts and only charge about $4 a day. They also have fully stocked tool boxes, (gotta love the military).
Though I am not military, (Civilian Contractor) my base ID gives me access.
So there may be an option here! I will have to read up and study the procedure, exactly. Any more advice will be greatly appreciated.
BTW, I went back over to my bike with my spare battery, started it up and then disconnected the battery. The instant I did, the engine died.
|05-21-2017 12:33 PM|
That's a bummer to hear man. If you could ever get the bike up here to Jacksonville with the parts in hand we could knock it out in a weekend I think. I have all the tools since I just did the balancer job which is just 3 bolts and a couple solder points shy of the stator job.
Probably a long shot but having a garage is a gift to be shared I reckon
|05-21-2017 11:53 AM|
Originally Posted by michiganteddybear View Post
Here's this morning's numbers after reading through the multimeter manual.
1: Resistance (Case to Stator Wires)
A: 00.5 ohms, B: 00.7 ohms, C: 00.9 ohms
2:Resistamce (Between the Three Poles)
AB: 00.7 ohms, AC: 00.9 ohms, BC: 01.1 ohms
Still no running voltage check as my battery is out and on a charger.
I live in an over 55, gated park. Motorcycles are not allowed in the park, though there are several bike owners here besides myself. All motorcycles have to be parked in the bike spaces behind the park office, near the front gate.
So besides sitting on the hot asphalt in 90 to 100+ degree temps, the park Association People would go out of their minds if I started doing a job like that.
They have some pretty stupid rules here but I've always maintained I didn't come down here to start challenging the parks rules, I came down for my job.
They don't allow any pets, of any kind. If you drove up to the gate with a dog in your car and said you were here to pick me up, they would not admit you because of the dog. I'd have to walk out to the gate.
It's ungodly expensive to live in the Keys. I'm renting my lot from a family friend so my lot rent is well below the local average down here, (today's SJW types would claim that I am "unfairly privileged") and it's only five minute from the park gate to main gate at the base so there is a financial advantage to stay where I am.
|05-21-2017 10:12 AM|
what kind of facilities do you have available to you in Key West? (driveway, carport, garage if your lucky?)..
I just did my stator in my parking lot where I live. pulled engine one day, repaired and reinstalled following day.
Not much special in tools required, a good metric socket set is about it (you will also need 1 allen wrench, 8mm I think, for removing the right side frame), and a floor jack or some other way to support engine when removing it.
will also add that total removal is NOT required, Others have just loosened it, pulled it out a little and tilted the engine to get the clearance to pull the cover.
also, we ALWAYS recommend replacing the balance dampers while your in there, as your only 2 bolts away from them.
|This thread has more than 10 replies. Click here to review the whole thread.|