WilliamTech3 WilliamTech3 is offline
- About WilliamTech3
- All stock 86 VN750 w/CustomAcessories
- Avoiding Back Pain -LOL
- Ebay Username
- Originally WilliamTech
Since May 2011
86 VN750 13,700 mi -Stock -Purchased 2008 w/8800mi
Replaced ALL Cables . Kuryakyn LED Voltmeter
Jardine Fwd Controls, Custom Fenders w/Rails
Iridiums DPR7EIX-9 & Wires, Tuxedo Mod, Coil Mod, P/U Sensor Mod, Fork Seals,
Splines Lubed - 11/4/2012 - MF AGM Battery, Dampers went out @ 13+K !
After TOC MCCT's..... so amazingly quiet I discovered a rattling heat shield on my stock exhaust !
...have a Vulcan good day !
- Originally WilliamTech
- Total Albums: 1
- Total Pictures: 0
- Albums Created by WilliamTech3
- Total Messages: 6
- Most Recent Message: 08-09-2019 09:26 AM
- Visitor Messages for WilliamTech3
- Last Activity: 02-27-2019 08:18 AM
- Join Date: 11-24-2017
- Referrals: 0
|09:23 PM - WilliamTech3 quoted MileHighVulcan in post Choke Question
=/ Hate taking that carb out, I'm a...
|11:12 AM - Jason Pittenger quoted WilliamTech3 in post Removed Mufflers - - Results
...east. :motorcycl WilliamTech3 For better or wor...
|11:01 PM - WilliamTech3 quoted shark88 in post Gas tank mounts keep cracking
License plate I've had snap,...
|06:14 PM - WilliamTech3 quoted OleDirtyDoc in post
|11:12 AM - WilliamTech3 quoted OleDirtyDoc in post New member
Welcome to the nucking futhouse....
|10:01 PM - freeman08 quoted WilliamTech3 in post Checking In
...light training ? WilliamTech3 I don't planning ...
|03:11 PM - WilliamTech3 quoted jdolbear in post Starter button repair
Hi all, New member here. I...
|12:53 AM - WilliamTech3 quoted shark88 in post How to recognize exhaust?
They also kinda look like th...
|09:33 PM - WilliamTech3 quoted TechMech in post Starter Relay - 2 pin connector
The starter relay has a two p...
|12:43 PM - WilliamTech3 quoted Jason Pittenger in post Removed Mufflers - - Results
Here are pictures with the muffler's...
|11:16 AM - WilliamTech3 quoted Goofyfoot2001 in post
|01:44 PM - WilliamTech3 quoted One1 in post 'nother stator job
I am running synth as wel...
|11:22 AM - WilliamTech3 quoted ubertalldude in post need suggestions
No, those are accessory leads. Th...
|12:15 PM - WilliamTech3 quoted 1stVulcan750 in post check in
Hi my names Daniel from San Angel...
|11:13 AM - WilliamTech3 quoted ubertalldude in post Factory Saddlebag Brackets
I think Scott2006 is asking Vulca...
|11:07 AM - WilliamTech3 quoted Spockster in post One carb only
...y engine vacuum. Spockster, would centerstand s...
|11:01 AM - WilliamTech3 quoted Scott2006 in post Factory Saddlebag Brackets
Where would I ship them to in ...
|07:33 PM - WilliamTech3 quoted Leo Kirsch in post Engine won't crank, tried everything
Battery is fully charged. Opene...
|01:42 AM - WilliamTech3 quoted Watzilla in post Check in
Just checking in, my name is ...
|01:30 AM - WilliamTech3 quoted Andeo1025 in post Possible rotor failure
Well I opened up the engine to...