Needing parts - Kawasaki Vulcan 750 Forum : Kawasaki VN750 Forums
Sell or Swap
Got a part you want to sell or looking for a part?
Want to trade for something? Post it in here!

Reply
 
LinkBack Thread Tools Display Modes
post #1 of 12 (permalink) Old 07-30-2012, 12:47 AM Thread Starter
Senior Member
 
Join Date: Jul 2012
Posts: 384
iTrader: (-3)
 
Needing parts

I am in need of a set of handlebars for my 85 700.
The PO dropped it on the left side, and the front end is tweaked, and the bars are bent.
I'm also in need of a tool box with key.
Thanks all.
TSmith68 is offline  
Sponsored Links
Advertisement
 
post #2 of 12 (permalink) Old 07-30-2012, 11:52 PM
_R_
Member
 
Join Date: Jul 2012
Location: St Charles, MO
Posts: 45
iTrader: (4)
 
i have a set of handlebars from my 93 750. please pm me.
_R_ is offline  
post #3 of 12 (permalink) Old 07-31-2012, 02:14 AM Thread Starter
Senior Member
 
Join Date: Jul 2012
Posts: 384
iTrader: (-3)
 
PM Sent _R_
TSmith68 is offline  
 
post #4 of 12 (permalink) Old 07-31-2012, 08:51 AM
_R_
Member
 
Join Date: Jul 2012
Location: St Charles, MO
Posts: 45
iTrader: (4)
 
PM replied.
_R_ is offline  
post #5 of 12 (permalink) Old 07-31-2012, 05:07 PM Thread Starter
Senior Member
 
Join Date: Jul 2012
Posts: 384
iTrader: (-3)
 
I am going to need a temp sensor that goes on the thermostat housing. The PO broke the tab off of the top of it.
I'm going to try to solder a tab on it and see if I can get it to hold. Or I might even try to solder a wire on there and crimp a connector on there to hook to the main gauge.
That shouldn't change the resistance should it? If I use a piece about an inch long or so?
TSmith68 is offline  
post #6 of 12 (permalink) Old 07-31-2012, 06:01 PM
..have a vulcan good day!
 
WilliamTech's Avatar
 
Join Date: May 2011
Location: Pensacola, FL.
Posts: 4,508
iTrader: (17)
   
Quote:
Originally Posted by TSmith68 View Post
I am going to need a temp sensor that goes on the thermostat housing. The PO broke the tab off of the top of it.
I'm going to try to solder a tab on it and see if I can get it to hold. Or I might even try to solder a wire on there and crimp a connector on there to hook to the main gauge.
That shouldn't change the resistance should it? If I use a piece about an inch long or so?
been there - done that !
---not a problem. No resistance change that matters.
If need be, you can dremmel some of the plastic casing, in order to have enough to solder to.

Williamtech

'86 VN750 13,700 mi -Stock
-Purchased 2008 w/8800mi
Replaced ALL Cables . Kuryakyn LED Voltmeter
SilverStar Ultra 9003/HB2 H4 Headlamp, Jardine Fwd Controls,
Iridiums DPR7EIX-9 & Wires, Tuxedo Mod, Coil Mod, P/U Sensor Mod, Fork Seals,
Splines Lubed - 11/4/2012 - MF AGM Battery
Additional Flashing LED Brake Light on Trunk
Dampers went out @ 13+K !
After TOC MCCT's..... so amazingly quiet I discovered a rattling heat shield on my stock exhaust !
...have a vulcan good day!
WilliamTech is offline  
post #7 of 12 (permalink) Old 07-31-2012, 08:24 PM
ass hole extaordinaire
 
new rider 9984's Avatar
 
Join Date: May 2012
Location: Sulphur Springs TX
Posts: 3,780
iTrader: (7)
 
same thing happened to mine tab broke off i just stripped back the wire and wrapped it around between the metal that was left and the plastic and it's still working
new rider 9984 is offline  
post #8 of 12 (permalink) Old 08-01-2012, 01:23 AM Thread Starter
Senior Member
 
Join Date: Jul 2012
Posts: 384
iTrader: (-3)
 
This one broke clear off down to the top of the sensor. There is a small tab left to try and solder a lead to it to hook up a wire.
Those damned sensors are $32.90 at Ron Ayers.
TSmith68 is offline  
post #9 of 12 (permalink) Old 08-01-2012, 02:52 AM
ass hole extaordinaire
 
new rider 9984's Avatar
 
Join Date: May 2012
Location: Sulphur Springs TX
Posts: 3,780
iTrader: (7)
 
saw one on ebay for 15 bucks or so
you might be able to take it off and have o reallys or idiot zone match it up
new rider 9984 is offline  
post #10 of 12 (permalink) Old 08-31-2012, 03:16 PM
Senior Member
 
Mcneuby's Avatar
 
Join Date: Jun 2010
Location: Close to Peoria Illinois
Posts: 509
iTrader: (18)
 
The parts you wanted

I have the siderails,the sissy bar, the handlebars and the tool box in a box ready to ship. I just wanted to ask if you have my mailing address to mail the money order you talked about.

Mcneuby
Mcneuby is offline  
Sponsored Links
Advertisement
 
Reply

Bookmarks

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Kawasaki Vulcan 750 Forum : Kawasaki VN750 Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

Once registered, your User Name"cannot be changed". We can make exceptions within 7 days, but after that, it is set in stone.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome